Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
searchwing-wing-servo [2020/02/02 13:10] beckmanf changed values, added closeup image |
searchwing-wing-servo [2020/02/03 18:52] (current) beckmanf Shorten cable, reduce transparent shrinking tube to 20mm |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| * [[https://www.digikey.de/product-detail/de/50-00601/839-1556-ND|Tensility M5 3-pin plug]], IP67, AWG26 (0.14mm2), 2.94€ | * [[https://www.digikey.de/product-detail/de/50-00601/839-1556-ND|Tensility M5 3-pin plug]], IP67, AWG26 (0.14mm2), 2.94€ | ||
| * [[https://www.digikey.de/product-detail/de/50-00604/839-1558-ND|Tensility M5 3-pin socket]], IP67, AWG26 (0.14mm2), 3.04€ | * [[https://www.digikey.de/product-detail/de/50-00604/839-1558-ND|Tensility M5 3-pin socket]], IP67, AWG26 (0.14mm2), 3.04€ | ||
| - | * [[https://m-el.eu/details/61001|Muldental Schrumpfschlauch 1,2mm black]] | + | * [[https://m-el.eu/details/61011|Muldental Schrumpfschlauch 1,6mm black]] |
| * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparent mit Kleber]] | * [[https://m-el.eu/details/62106 |Muldental Schrumpfschlauch 4mm/1mm transparent mit Kleber]] | ||
| Line 22: | Line 22: | ||
| {{:sw-servo-m5-to-pixracer.jpg?600|Solder view}} | {{:sw-servo-m5-to-pixracer.jpg?600|Solder view}} | ||
| - | * Cut 25mm of the transparent shrinking tube and put it on the cable | + | * Shorten the servo cable by 40mm |
| + | * Cut 20mm of the transparent shrinking tube and put it on the cable | ||
| * Separate the yellow, red and brown cable for about 5cm | * Separate the yellow, red and brown cable for about 5cm | ||
| - | * Add about 5mm of the 1.2mm shrinking tube to the red and the brown cable. | + | * Add about 5mm of the small shrinking tube to the red and the brown cable. |
| * Move the shrinking tubes as far as possible from the solder spot to avoid accidental shrinking | * Move the shrinking tubes as far as possible from the solder spot to avoid accidental shrinking | ||
| * Remove the isolation for about 4mm and twist and tin the wires. | * Remove the isolation for about 4mm and twist and tin the wires. | ||
| Line 48: | Line 49: | ||
| The next image shows the small shrinking tubes moved over the solder connections. | The next image shows the small shrinking tubes moved over the solder connections. | ||
| - | {{:sw-m5-shrinking-tube.jpg?600|Socket with 1.2mm shrinking tubes}} | + | {{:sw-m5-shrinking-tube.jpg?600|Socket with shrinking tubes}} |
| * Now shrink the black shrinking tubes with a heat gun. With the Heinel EL 1910 E heat gun select temperature "3" with maximum air speed. | * Now shrink the black shrinking tubes with a heat gun. With the Heinel EL 1910 E heat gun select temperature "3" with maximum air speed. | ||