Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
searchwing-antenna-ground-box [2021/11/10 13:59] beckmanf add AGS V2 |
searchwing-antenna-ground-box [2022/04/02 09:42] (current) beckmanf [Antenna ground box] add header datasheet |
||
|---|---|---|---|
| Line 7: | Line 7: | ||
| * [[https://www.pusr.com/products/serial-to-ethernet-converter-modules-usr-tcp232-t2.html| USR-TCP232-T2 - UART to Ethernet Converter]] | * [[https://www.pusr.com/products/serial-to-ethernet-converter-modules-usr-tcp232-t2.html| USR-TCP232-T2 - UART to Ethernet Converter]] | ||
| * [[https://www.gl-inet.com/products/gl-ar750/|GL-AR750]] access point to access mavlink via Wifi | * [[https://www.gl-inet.com/products/gl-ar750/|GL-AR750]] access point to access mavlink via Wifi | ||
| - | * The [[searchwing-rf-antenne|RFD868+ Modem]]. | + | * The [[searchwing-rf-antenne|RFD868+ Modem±Õ±ÕÌý |
| + | * The Datasheet of the {{ ::ds_mpe_095.pdf |Angled Header}} available at [[https://www.reichelt.de/buchsenleisten-2-54-mm-2x10-gewinkelt-mpe-095-2-020-p119921.html?&nbc=1|Reichelt]]. | ||
| In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. | In addition it is possible to connect via the [[https://www.ftdichip.com/Support/Documents/DataSheets/Cables/DS_TTL-232R_CABLES.pdf|FTDI UART/USB]] cable with and without power from the 24V system. The router can also be connected with an ethernet cable to have wired access to the telemetry data. | ||
| + | |||
| + | [[searchwing-antenna-ground-box#antenna_box_v2|Current Version V2]] | ||
| + | |||
| + | ==== Antenna Box V1 ==== | ||
| {{ ::basestationplatine.png?600 |}} | {{ ::basestationplatine.png?600 |}} | ||
| Line 81: | Line 86: | ||
| ==== Antenna Box V2 ==== | ==== Antenna Box V2 ==== | ||
| - | A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "Hutschiene". | + | A new PCB board integrates the voltage regulator, RFD868+ modem, UART to Ethernet Converter on one board. Everything is now installed via "Hutschiene". This version was installed on the [[https://www.hs-augsburg.de/searchwing/de/seawatch-tests-2021/|mission with Sea-Watch 4 with Philipp]]. |
| === Electronics / Board === | === Electronics / Board === | ||
| - | Franc and Tim design a board for the antenna ground box. | + | Franc and Tim designed a board for the antenna ground box. |
| {{ ::sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}} | {{ ::sw-ags-pcb-v2.jpg |Antenna Ground Station PCB v1.0 with Hutschienenadapter}} | ||
| - | **Fig. 4:** Antenna Ground Station v2 with PCB v1.0 with Hutschienenadapter | + | **Fig. 4:** Antenna Ground Station PCB v1.0 with Hutschienenadapter |
| Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at | Figure 4 shows the antenna ground box PCB version 1.0. The design data is available at | ||
| Line 95: | Line 100: | ||
| [[https://easyeda.com/SearchWing/antennagroundstation|Easyeda - Antenna Ground Station PCB Board]] | [[https://easyeda.com/SearchWing/antennagroundstation|Easyeda - Antenna Ground Station PCB Board]] | ||
| - | The pcb board installed with Hutschiene inside the Spelsberg box. | + | The pcb board is installed with Hutschiene inside the Spelsberg box. |
| {{ ::sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}} | {{ ::sw-ags-box-v2.jpg | Antenna Ground Station v2 with PCB and Hutschiene}} | ||